Voltage 240 VAC Wattage per SF 12 Watts per Sq Foot Heating Power Output per Hour 41 BTU per Sq Ft/Hour Heating Power Output Total 1230 BTU total Length of Heated Area (ft) 12' ft. feet Full Length End-to-End ground wire Yes Length of Heated Area (in) 144" in. inch Width of Heated Area (in) 30" in. inch Power Lead Type Armored, NEC color code, Single point connection at 1 corner of mat. No return wire like inferior products Power Lead Length 10 Feet Power Lead Wire Gauge 18 AWG Thickness 0.122 (less than 1/8") Spacing of Heating Wire 2.50 inches Ohms Reading (resistance value) 155-190 ohms EMF (Electro Magnetic Field) Yes. Verified by Independent Testing Laboratory as ultra low. REET test Thermostat Control Required? SunStat Floor sensing thermostat Conduit Required? Conduit does make installation easier in new construction (not required)
- Instructions + Video
Instructions + Video
Instruction Manual SunTouch 24001230ST Mat 240V 30"x 12' 24001230 Installation Manual VIDEO Skill Level Installation only by qualified persons. Electrician recommended for wiring. Read More GFEP / GFCI Protection (Ground Fault Circuit Interrupter) Required for each circuit. Built-in to all SunTouch SunStats. Circuit Breakers and Supply Wire (always follow local code) Mats or Wire Supply Wire Breaker VAC total amps (AWG*) qty type rating 120 up to 12 amps 14 1 single pole 15 or 20 A 120 up to 15 amps 12 1 single pole 20 A 240 up to 12 amps 14 1 double pole 15 or 20 A 240 up to 15 amps 12 1 double pole 20 A
* Recommended only. Follow local codes for wire gauge size.
Maximum Circuit Overload Protection 20 A Breaker Maximum Circuit Load 15 Amps Electrical Box Size Extra-deep single-gang box for 1 or 2 leads, Or 4" square deep box for 3 cables (extra room needed for Wire, wire nuts, control) Shower Installation Yes, can be installed in a tiled shower. UL listed, verify local code. Layout Flexibilty Yes Expected Floor Temperature This is dependent on many factors. A well-insulated floor can ensure better performance. Insulation Recommended Yes; under slabs or framed floors. Cork or similar on top of Concrete Subfloor as thermal break Indoor / Outdoor INTERIOR floor heating Application only. Embedded in Mortar or self leveling concrete only Installation On Sub Floor on TOP of Sub Floor (Plywood, backer board, concrete) Distance from Wax Ring at toilet flange Install 4 - 6 inches away; can be under front of toilet. Approx 20" from wall Trowel Size recommended Minimum 3/8" x 1/4". Dependent on tile size - verify with tile/mortar manufacturer Trowel type Recommended Heavy Duty Plastic PRO-Trowel Minimum Bend Radius 1 inch Cut Warning No. Never cut the heating elements to shorten Minimum Installation Temperature 50 Degrees F / 10 Degrees C
- More Details
Manufacturer Watts Radiant Flooring Type Tile & Stone, Engineered Hardwood, Laminate, Vinyl, Concrete, Carpet Why Helps
SunTouch = Zero EMF
An emerging issue in the electric radiant heat industry is EMF (electromagnetic field) radiation. SunTouch pioneered and sells only ZERO EMF products constructed with active dual wire EMF-canceling technology.
All SunTouch products use a complex wire construction with two heating elements in parallel with an added and patented helical twist to eliminate EMF. Other electric radiant floor heating companies sell single-wire systems that release high levels of EMF when compared to SunTouch.
What is EMF? Electromagnetic fields (EMF) come from all electrical appliances, but studies show an average American's daily exposure is less than 1 unit (mG) of EMF. But. when you sit on an unshielded electric radiant floor, you may be exposed to 20, 40, or more times the average daily exposure. This Data comes from Independent testing. Read More Here
Is limiting exposure to EMF important? No one is certain. The World Health Organization says the data is inconclusive to date, but continues their research. We provide this EMF information because it is important to some people, not to frighten you or exaggerate any risk.
For many years customers have chosen SunTouch Zero EMF systems, but we leave the choice to you after explaining what we do know.
Warranty from Manufacturer 25 year warranty backed by USA Manufacturer since 1873 Amp Draw 1.5 Heated Area $30.00 Heating Wire ETFE Fluoropolymer, metal shield and Outside layer of PEX Size in Inches 30" x 144" (30x144 inches) Size in Feet 2.5' x 12' (2.5x12 feet) Total Watts 360 watts Installation Style Open Mesh Mat. Heating wire secured to Mat with Tape. Requires tape, staples or glue to attach to floor. Custom Size Options None. Standard Mats only. Repairable Heating Wire Yes, Wire can be repaired. Repair kits and assistance available Safety Listing UL (Underwriters Laboratory) Listed for U.S. and Canada under UL 1673 and CAN/CSA C22.2 No. 130-03, File No. E185866 Acceptable Floor Coverings Natural Stone,Tile, Laminate, Engineered Woods, Carpet, Vinyl, Linoleum, Solid Hardwood (if you use sleepers) Made In USA Made in USA Expected Order Shipping Same day the order is placed
You might also like...
SunStat Connect WiFi Enabled Programmable Thermostat$270.00
KERDI-DRAIN KIT with 2" PVC Flange & 4" Stainless Steel Grate
You Save: $12.68
HeatTrak 20" x 60" • Residential Heated Walkway power cord sold separately (HR20-60)
You Save: $20.00
KERDI-SHOWER-KIT 32" x 60" Centered Stainless Steel Drain with PVC Flange
You Save: $56.99