Nuheat standard size pre-built floor heat mats come ready to fit the room and will keep almost any flooring at a warm and comfortable temperature that you set on the Nuheat thermostat control.
You can use more than one Nuheat mat combined to fit any room size or shape, up to the amp limit of the thermostat (150 SF for 120v / 300 SF for 240v Mats). All Mats connect to the Thermostat, not to each other.
Nuheat mats are like electric blankets - you choose the size or sizes to cover your desired floor area - or ask for our expert assistance at NO OBLIGATION. The mats cannot be cut or altered - so choose the right size - we can help.
UPC 620713001127 Voltage 240 VAC How to choose 120 or 240 Volt Same Energy efficiency & same Watts/SF. More Sq Footage per circuit with 240v Amp Draw 1.7 Watts Per SF 12 Watts per Sq Foot Total Watts 414 watts Heat Output BTUs per SF 41 BTU per Sq Ft/Hour Heating Power : Total BTU's 1394 BTU total Manufacturer Pentair Power Lead Type TEW Wire with Stainless Steel ground braid rated to 105 C and 300v max. Power Lead Length 10 Feet Power Lead Wire Gauge 18 AWG Thickness Mat is .083, total is 1/8" with thinset underneath. Full Length End-to-End ground wire Yes. Heating Wire Spacing 2.0" inches Minimum Bend Radius 0.625" inch Ohms Reading (resistance value) 133 - 153 ohms Controls/Thermostat is required for operation Nuheat Floor sensing thermostat Conduit required for Power Leads Nuheat mats require conduit Packaging Easy Open Cardboard - no frustration Length of heating area Feet 3.5' ft. feet Length of heating area Inches 42" in. inch Width of heating area Inches 118" in. inch
- Instructions + Video
Instructions + Video
Instruction Manual Nuheat G3010 Mat 240V 118" x 42" G3010 Installation Manual Video Install Steps
Nuheat mats are squares and rectangles in over 120 sizes and will fit any room regardless of shape or size. When installing your floor, the heating mats are set in a thin spread of mortar (the same bonding materials used to lay your tile floor). Once your subfloor is prepared, and you have installed the Nuheat mat, apply another layer of thinset or mortar, lay your tile as usual and make the final connection to the Nuheat Thermostat control.
Laminate & Engineered Hardwood: simply install the Nuheat mat as above. Next, cover the Nuheat mat with at least 1/4 inch mortar or floor leveling cement. Once the mortar has cured, install your floor according to the flooring manufacturer's instructions.
Skill Level Installation only by qualified persons. Electrician recommended for wiring. Maximum Circuit Load 15 Amps Maximum Circuit Overload Protection 20 A Breaker. GFEP / GFCI Protection (Ground Fault Circuit Interrupter) Required for each circuit. Built-in to all Nuheat thermostats. Electrical Box Size (Where Mats connect to Thermostat) Extra-deep single-gang box for 1 or 2 leads, Or 4" square deep box for 3 cables (extra room needed for Wire, wire nuts, control). Harmony requires 4" box. Shower Installation Yes, can be installed in a tiled shower. Installation Layout Map customized for my project Yes. Contact us for more information. Expected Floor Temperature This is dependent on many factors. A well-insulated floor can ensure better performance. Insulation Recommended Yes; under slabs or framed floors. Cork or similar on top of Concrete Subfloor as thermal break Indoor / Outdoor INTERIOR floor heating Application only. Embedded in Mortar only Installation On Sub Floor On TOP of Sub Floor (Plywood, backer board, or concrete) Distance from Wax Ring at toilet flange Install 4 - 6 inches away; can be under front of toilet. Approx 20" from wall Trowel Size recommended minimum 3/8" x 1/4". Works for most ceramic tile; verify with tile/mortar manufacturer Trowel type Recommended Heavy Duty Plastic PRO-Trowel Cut Warning No. Never cut the heating elements to shorten Minimum Installation Temperature 50° Degrees F / 10° Degrees C
- More Details
What's In The Box Nuheat Mat, Complete instructions. Installation videos online. Warranty from Manufacturer 25 year warranty Heating Wire Copper/Copper Alloy Heating wire insulated with ETFE and surrounded with protective Stainless steel ground shield. Heated Area $34.42 Size in Inches 118" x 42" (118x42 inches) Size in Feet 9.83' x 3.5' (9.83x3.5 feet) Installation Style Fiber mat. Heating wire sandwiched completely in the material. Requires thinset mortar under mat to attach to floor. Custom Size Options Yes, custom mats available upon request Safety Listing UI (US) 1693; UL (CAN/CSA) C22.2 #217; NEC Article 424 Floor Warming Systems Repairable Heating Wire Yes, Wire can be repaired. Repair kits and assistance available. Acceptable Floor Coverings Tile, Stone,Granite, Marble, Slate, Engineered wood, Laminate Made In USA Made in Canada from a majority of USA components.
You might also like...
SunStat Connect WiFi Enabled Programmable Thermostat$270.00
KERDI-DRAIN KIT with 2" PVC Flange & 4" Stainless Steel Grate
You Save: $12.68
HeatTrak 20" x 60" • Residential Heated Walkway power cord sold separately (HR20-60)
You Save: $20.00
KERDI-SHOWER-KIT 32" x 60" Centered Stainless Steel Drain with PVC Flange
You Save: $56.99
Nice upgradeUpdated our bathroom and put new tile floor in with heat mat. No more cold feet. Love it.