SunTouch SlabHeat Cables are the best solution for true radiant floor heating installed within a new concrete slab pour.
SlabHeat is engineered by the world leader in electric floor heating systems with the capability to produce enough BTUs to heat a slab, the space, and the surface people walk on. Regardless of size, shape, or thickness, SlabHeat is the way to provide heat to just about any indoor space.
Benefits of SlabHeat
Tough polyurethane outer jacket offers superior flexibility, abrasion and tear resistance, impact resistance, resiliency and better low temperature stability than the PVC used in competing products.
- Safety built in ZERO EMF dual wire cables are UL Listed
- Engineered by Watts Radiant SunTouch a company with decades of experience in hydronic and electric radiant heating
- Comfortable, even heat without the drying effects of forced air heating
- Reliable, durable design
- No vents or duct work
- Invisible with no lost space - not like large intrusive base board heaters
- Maintenance-free and silent
- Efficient radiant heat of up to 51 BTUs per Sq Ft
SlabHeat Cable is a complete heating cable consisting of a series resistance heating cable and a single power lead for easy single point connection. The heating cable length cannot be cut to fit. Constant wattage output is approximately 5 Watts per Linear Foot.
SlabHeat cable should be installed in all interior floor areas to be warmed. It cannot be used for exterior applications, snow melting, or in ceilings.
Primary Heat Applications
A properly designed heating system begins with an accurate heat-loss calculation to determine whether the system will provide enough energy to function as the primary heat source for the space or provide floor warming only. If it is a primary heating system, we recommend a detailed heat-loss be performed first, then select wire spacing based on heat output. If you have already know the BTUs required, the calculation is simple. If you need us to perform a heat-loss calculation, please download the form and return it to us with all details completed.
Voltage 120 VAC How to choose 120 or 240 Volt Same Energy efficiency & same Watts/SF. More Sq Footage per circuit with 240v Watts Per SF 15 Watts per Sq Foot (at 4" in. inch spacing) Heat Output BTUs per SF 51 BTU per Sq Ft/Hour @ 4" in. inch spacing) Heating Power : Total BTU's 5100 BTU total Manufacturer Watts Radiant Power Lead Type Armored, NEC color code, Single point connection at 1 end of spool. No return wire like inferior products Power Lead Length 10 Feet Power Lead Wire Gauge 14 AWG Thickness 1/4 " in. inch Heating Wire Spacing 4" - 5" - 6" on center Full Length End-to-End ground wire Yes. Ohms Reading (resistance value) 7 - 10 ohms EMF (Electro Magnetic Field) Yes. Verified by Independent Testing Laboratory as ultra low. REET test Controls/Thermostat is required for operation SunStat Floor sensing thermostat BTUs/SF/Hr 1 51 BTUs/SF/Hr 2 42.5 BTUs/SF/Hr 3 34 Spacing between runs 1 4 Spacing between runs 2 5 Spacing between runs 3 6 Watts Per SF 1 15 Watts Per SF 2 12.5 Watts Per SF 3 10 Heated SF 1 100 Heated SF 2 124 Heated SF 3 149 Packaging Easy Open Cardboard - no frustration. Easy to dispense cable from spool Length of heating area Feet 294' ft. feet Length of heating area Inches 3528" in. inches
- Instructions + Video
Instructions + Video
Instruction Manual SlabHeat SH15120100ST Cables 100 Sq Ft 120V Radiant Slab Heating Cable Installation Manual GFEP / GFCI Protection (Ground Fault Circuit Interrupter) Required for each circuit. Built-in to all SunTouch SunStats. Circuit Breakers and Supply Wire (always follow local code) Mats or Wire Supply Wire Breaker VAC total amps (AWG*) qty type rating 120 up to 12 amps 14 1 single pole 15 or 20 A 120 up to 15 amps 12 1 single pole 20 A 240 up to 12 amps 14 1 double pole 15 or 20 A 240 up to 15 amps 12 1 double pole 20 A
* Recommended only. Follow local codes for wire gauge size.
Maximum Circuit Load 15 Amps Maximum Circuit Overload Protection 20 A Breaker. Recommended Insulation Resistance test by Electrician Use a Megohmeter - see manual Electrical Box Size (Where Mats connect to Thermostat) Extra-deep single-gang box for 1 or 2 leads, Or 4" square deep box for 3 cables (extra room needed for Wire, wire nuts, control) National Electric Code reference ANSI/NFPA 70 especially Article 426. Plus any local code requirements Skill Level Running Cable more difficult + more time than MATS. Installation only by qualified persons. Electrician recommended for wiring. Read More Minimum Depth .75" inches below top of heated surface-completely covered Recommended Method and Depth for Slab 1.50" to 2" inches below top of heated surface-completely covered Maximum exposure temperature 194 ° degrees F Installation Layout Map customized for my project No, example in manual. We provide Layout Maps only for MATS Expected Floor Temperature This is dependent on many factors. A well-insulated floor can ensure better performance. Insulation Recommended Insulated slab recommended Indoor / Outdoor Indoor Installation Only Inside Concrete Slab Installation On Sub Floor Installation On Sub Floor covered by 3/4" concrete (slab cap) Distance from Wax Ring at toilet flange Install 4 - 6 inches away; can be under front of toilet. Approx 20" from wall Minimum Bend Radius 1" 1 inch Cut Warning No. Never cut the heating elements to shorten
- More Details
Warranty from Manufacturer 10 year warranty backed by USA Manufacturer since 1873 Amp Draw 12.5 Heating Wire Thermoplastic insulation, metal shield and Outside layer of Polyurethane Cable Length 294' ft. feet Cable Length (inches) 3528" in. inch Cable Length (meters) 89.09 m meter metre Heated Area $100.00 Total Watts 1500 watts - Total watts are per cable, NOT dependent on spacing Custom Size Options None. Standard lengths only. No customization Repairable Heating Wire Yes, Wire can be repaired. Repair kits and assistance available. Safety Listing UL (Underwriters Laboratory) Listed for U.S. and Canada under UL 1673 and CAN/CSA C22.2 No. 130-03, File No. E185866 Canadian Electric Code reference Section 62 (CEC) Part I. Plus any local code requirements Made In USA Made in USA
HeatTrak 10" x 30" • Residential Heated Stair Mat - power cord sold separately (HR10-30)
You Save: $10.00
HeatTrak 20" x 60" • Residential Heated Walkway power cord sold separately (HR20-60)
You Save: $30.00
KERDI-SHOWER-KIT 32" x 60" Centered Stainless Steel Drain with PVC Flange
You Save: $56.99
KERDI-DRAIN KIT with 2" PVC Flange & 4" Stainless Steel Grate
You Save: $12.68