- Thinner installation (RPM = 5/16" vs. Backerboard = 1/2") helping you match up a variety of flooring materials.
- Thermal Break over concrete slab.
- Lightweight and durable recyled materials makes RPM Mats simple to use
- Easy and mess-free to cut with a utility knife right on the job site.
- Provide a customizable grid to evenly run floor heating wire under floors.
- Heating wire sits below RPM studs, keeping you off the wire and unable to trip or pull out the heating wire during installation.
- Reduces risk of damage to heat wire and integrity of floor heating system.
- Wire stays below trowel level when spreading leveling cement.
- Can be used with any brand of heat wire.
Snow & Ice Melting
Never shovel snow again! Snow and Ice Melting systems enhance the safety of your outdoor areas. Heated Driveways and walkways provide a snow free path without shoveling or nasty salts or chemicals.
Permanent systems, like ProMelt mats and cables, can be installed within new walkways or driveways provide years of invisible and durable snow melting results, whether it is a new concrete or asphalt heated driveway or a heated walkway of pavers or tile and even heated stairs for safe passage to your front door. These permanent snow melting systems are attached to rebar in new concrete pours, in sand under pavers or in new asphalt layers even on top of existing slabs and then covered by mortar and materials like flagstone, bluestone, etc.
You can even use these snow melting systems to provide comfort on patios to take the chill off cool evenings with up to 170 BTU’s per Sq Ft heat output.
HeatTrak’s portable snow melting mats are another solution for foot traffic areas (not driveways) that are already in place. We offer several size solutions in both a lighter duty Residential series for heated sidewalks and steps plus a heavy duty commercial-industrial series of mats that are used by many homeowners as well as hotels, ski resorts, and all types of businesses.
Our PriceOur Price: $451.00The PM-224 sensor uses a heated moisture sensor mounted on its top to detect both precipitation and temperature to activate a Contractor Pro control panel to power ProMelt Mats or Cables. It is meant to be pole-mounted where it is open to the sky and elements. Learn More
Our PriceOur Price: $1,169.00The PM-090 Snow/Ice Sensor is an in-ground sensor that automatically detects snow or ice on a driveway or walkway. This sensor allows the PM-653 Snow Melting Control to automatically operate the snow/ice melt system only when snow or ice is present, while also providing slab temperature feedback to the control. Must be installed with PM-091 Sensor Socket. Learn More
Our PriceOur Price: $1,909.00The PM-HSC5 is a surface mounted snow detector. It is used to detect snowfall and low temperature and then automatically activate the ProMelt Mats or Cables via a CP panel. It has built-in temperature and moisture detection and a drying cycle (not adjustable) after snow melting is complete. It is comprised of a sensor and sensor socket that is embedded in the slab level with the surface where ProMelt is installed. Learn More
List Price: $450.00
Our Price: $338.00The SST-2 Freeze Protection Thermostat is designed to replace electromechanical thermostats for Nuheat Snow and Ice Melting systems for more cost-sensitive applications without sacrificing GFCI protection. The SST-2 activates heating cables at temperatures below 40F (4.4C) and turns them off at temperature above 42F (5.5C). Learn More
Our PriceOur Price: $506.00The PM-5 sensor-controller uses a heated moisture sensor mounted on its top to detect both precipitation and tempterature to activate the ProMelt Mats or Cables when conditions are right for snowfall. It is meant to be pole-mounted where it is open to the sky and elements. Learn More
Our PriceOur Price: $670.00The PM-L1 kit offers manual operation and monitoring of a snow melting system using a PM-653 touchscreen control. The PM-L1 Kit reduces the cost of snow melting by operating the system using the lowest possible temperature required to clear snow and ice. Kit includes a PM-653 touchscreen thermostat, a PM-072 slab sensor and outdoor temperature sensor. A ContactorPro panel is required to provide power for the mats, cables and control. Learn More
List Price: $295.00
Our Price: $233.00The RCU-4 is a remote control for Snow and Ice Melting Systems that can be used in conjunction with a GF Pro, APS-4C or SC-40C panel. It runs flush with the wall and has a light-up display that indicates when the system is running. Learn More