Voltage 240 VAC Wattage per SF 12 Watts per Sq Foot Heating Power Output per Hour 41 BTU per Sq Ft/Hour Heating Power Output Total 4100 BTU total Manufacturer Watts Radiant Power Lead Type Armored, NEC color code, Single point connection at 1 corner of mat. No return wire like inferior products Power Lead Length 10 Feet Power Lead Wire Gauge 14 AWG Thickness 0.122 (less than 1/8") Spacing of Heating Wire 3" inches Minimum Bend Radius 1 inch Resistance Value multiple EMF (Electro Magnetic Field) Yes. Verified by Independent Testing Laboratory as ultra low. REET test Thermostat Control Required? SunStat Floor sensing thermostat Conduit Required? Conduit does make installation easier in new construction (not required) Length of Heated Area (ft) 50' ft. feet Width of Heated Area (in) 24" in. inch Length of Heated Area (in) 600" in. inch
- Instructions + Video
Instructions + Video
Instruction Manual SunTouch24005024-KIT-MA TapeMat kit 24005024-kit-MA Installation Manual Install Steps
Plan Your Layout
Measure and draw a layout simple plan (or send it to us and let us draw a layout for you) mark your Thermostat location (starting point for mats) and what areas you want to warm. Expect to place mats everywhere you want warmth heat does not spread
Roll Out Mat(s)
Turn and cut mesh (if needed) to custom fit to your room. Attach mat to subfloor with the built-in tape then mount the SunStat and place floor temperature sensor between 2 heating wires.
Cover with Mortar
Cover mats with a cement based mortar, let it cure, then install your floor covering. If you are installing tile, you can install the tile when you apply the mortar. Connect mat power leads to your thermostat in parallel.
Skill Level Installation only by qualified persons. Electrician recommended for wiring. Read More VIDEO GFCI / GFEP Protection Required for each circuit. Built-in to all SunTouch SunStats. Power Supply & Wiring Mats or Wire Supply Wire Breaker VAC total amps (AWG*) qty type rating 120 up to 12 amps 14 1 single pole 15 or 20 A 120 up to 15 amps 12 1 single pole 20 A 240 up to 12 amps 14 1 double pole 15 or 20 A 240 up to 15 amps 12 1 double pole 20 A
* Recommended only. Follow local codes for wire gauge size.
Maximum Circuit Load 15 Amps Maximum Circuit Overload Protection 20 A Breaker Electrical Box Size Extra-deep single-gang box for 1 or 2 leads, Or 4" square deep box for 3 cables (extra room needed for Wire, wire nuts, control) Full Length End-to-End ground wire Yes Shower Installation Yes, can be installed in a tiled shower. UL listed, verify local code Layout Flexibilty Yes Expected Floor Temperature This is dependent on many factors. A well-insulated floor can ensure better performance. Insulation Recommended Yes; under slabs or framed floors. Cork or similar on top of Concrete Subfloor as thermal break Indoor / Outdoor INTERIOR floor heating Application only. Embedded in Mortar or self leveling concrete only Installation On Sub Floor on TOP of Sub Floor (Plywood, backer board, concrete) Distance from Wax Ring at toilet flange Install 4 - 6 inches away; can be under front of toilet. Approx 20" from wall Trowel Size recommended Minimum 3/8" x 1/4". Dependent on tile size - verify with tile/mortar manufacturer Trowel type Recommended Heavy Duty Plastic PRO-Trowel Cut Warning No. Never cut the heating elements to shorten Minimum Installation Temperature 50° Degrees F / 10° Degrees C
- More Details
What's In The Box TapeMat, SunStat Command Programmable Touch Screen Thermostat, Floor Sensor, LoudMouth, Sm. Roll of Double-sided Tape, Digital Multimeter. Detailed Installation Manual. Individual Items (2) 2' x 25' 24002524 Warranty 25 Year backed by 140 year old USA Manufacturer Why Helps
SunTouch = Zero EMF
An emerging issue in the electric radiant heat industry is EMF (electromagnetic field) radiation. SunTouch pioneered and sells only ZERO EMF products constructed with active dual wire EMF-canceling technology.
All SunTouch products use a complex wire construction with two heating elements in parallel with an added and patented helical twist to eliminate EMF. Other electric radiant floor heating companies sell single-wire systems that release high levels of EMF when compared to SunTouch.
What is EMF? Electromagnetic fields (EMF) come from all electrical appliances, but studies show an average American's daily exposure is less than 1 unit (mG) of EMF. But. when you sit on an unshielded electric radiant floor, you may be exposed to 20, 40, or more times the average daily exposure. This Data comes from Independent testing. Read More Here
Is limiting exposure to EMF important? No one is certain. The World Health Organization says the data is inconclusive to date, but continues their research. We provide this EMF information because it is important to some people, not to frighten you or exaggerate any risk.
For many years customers have chosen SunTouch Zero EMF systems, but we leave the choice to you after explaining what we do know.
Heated Area Size Covered 100 Amp Draw 5 Wire Construction ETFE Fluoropolymer insulation, metal shield and Outside layer of PEX combined with heating elements Total Watts 1200 watts Size in Feet 2' x 50' (2x50 feet) Size in Inches 24" x 600" (24x600 inches) Custom Size Options SunTouch offers Custom Mats pre-built at factory. Send in a drawing today to get a quote on a custom mat. Safety Listing UL (Underwriters Laboratory) Listed for U.S. and Canada under UL 1673 and CAN/CSA C22.2 No. 130-03, File No. E185866 Repair Information Yes, Wire can be repaired. Repair kits and assistance available Acceptable Floor Coverings Natural Stone,Tile, Laminate, Engineered Woods, Carpet, Vinyl, Linoleum, Solid Hardwood (if you use sleepers) Made In USA Made in USA
You might also like...
HeatTrak 10" x 30" • Residential Heated Stair Mat - power cord sold separately (HR10-30)$69.99
HeatTrak 20" x 60" • Residential Heated Walkway power cord sold separately (HR20-60)
You Save: $20.00
KERDI-SHOWER-KIT 32" x 60" Centered Stainless Steel Drain with PVC Flange
You Save: $56.99
KERDI-DRAIN KIT with 2" PVC Flange & 4" Stainless Steel Grate
You Save: $12.68