ProMelt · 2' x 36' Foot [13.0A] Electric Snow Melting Mat (277V / 50W)

Availability: In stock
SKU
SM5027703624
$727.00
+ Free Shipping!

ProMelt electric radiant snow melting mats install easily and quickly providing electrically heated driveways and walkways. Energy efficient and environmentally friendly snow and ice removal in the worst conditions is possible without using nasty chemicals or corrosive salt.

ProMelt heated snow melting mats are manufactured by SunTouch Watts Radiant (pioneers of indoor radiant heat) using superior quality snow melting cable attached to a reinforced tape grid simplifying installation while maintaining optimum spacing of cables. Plus, you can free the cable from the mat to fill in or fit steps, curved or angled spaces as needed.

ProMelt is an effective, reliable and invisible snow melting system that will serve you for many years. Typical projects of 300 SF or less simply require mats and a snow sensor-controller and are very affordable and convenient.

ProMelt Snow Melting Benefits:

  1. ProMelt mats install quicker and easier than cable systems with no spacing errors.
  2. Automatically activates only when needed means your driveway and sidewalks stay clear and you never forget to turn the system off.
  3. No plowing or scraping means your walkway and driveway look better and last longer.
  4. Maintenance Free permanent installation. Not like Hydronic systems (water) with pumps, boilers, etc
  5. Increase safety and reduce liability with ProMelt.
  6. No hazardous chemicals to damage your landscaping or the environment.
  7. No waiting for the plow or shovel to arrive - Dependable automatic snow sensor once moisture and temperature conditions are met activates ProMelt.
  8. Save Money - Eliminate snow removal labor costs.
  9. The best construction using premium materials means ProMelt is built to last.
  10. Increase the value of your home with an automatic ProMelt System.
Maximum exposure temperature

285°F (140°C) Short-term max. for asphalt covering

Minimum Installation Temperature

40°F (4.5°C)

Maximum Circuit Load

30 or 50 Amps @ 240v, depending on controls chosen

Maximum Circuit Overload Protection

70 A Breaker.

Recommended Method and Depth for Asphalt

Attach ProMelt over cooled asphalt base layer- Cover with hand shoveled final asphalt layer min 1.5 inch thick-DO NOT DRIVE machines on exposed ProMelt. Roll with small roller or compactor. - See Installation Manual

Recommended Method and Depth for Pavers in sand

Minimum 1.5 inches sand over cables, max paver thickness of 2.50 inches - See Installation Manual

Recommended Method and Depth for Slab

Use Chairs/dobies so rebar/Mesh ProMelt is attached to is in top 2" of slab - See Installation Manual.

Recommended Method and Depth for Pavers in Concrete

Maximum 2.50" total thickness over cables - See Installation Manual

Spacing of attachment to Mesh/Rebar or surface

Every 24" using plastic ties (no metal) for mesh, or nail through tape for surface

Recommended Method and Depth for Tile/Stone

1.25" minimum - See Installation Manual and TCNA guidelines

Minimum Depth

1.50" inches below top of heated surface-completely covered : See Installation Manual

Distance from Edges of Concrete/Asphalt

Minimum 6" from edge of slab or 12" for asphalt without a curb

Manufacturer Watts Radiant
Heating Power Output Total 12240 BTU total
Heating Power Output per Hour (BTU) 170 BTU per Sq Ft/Hour
EMF (Electro Magnetic Field) Yes. Verified by Independent Testing Laboratory as ultra low. REET test
Ohms Reading (resistance value) 17 - 22 ohms
Power Lead Type Insulated, NEC color code, Single point connection at 1 corner of mat. No return wire like inferior products
Power Lead Length 20 Feet
Power Lead Wire Gauge 14 AWG
Thickness 1/4" in. inch
Voltage 277 VAC
Spacing of Heating Wire 3" inches
Length of Heated Area (ft) 36' ft. feet
Length of Heated Area (in) 432" in. inch
Canadian Electric Code reference Section 62 (CEC) Part I. Plus any local code requirements
National Electric Code reference ANSI/NFPA 70 especially Article 426. Plus any local code requirements
Safety Listing ETL Listed for U.S. and Canada under UL (Underwriters Laboratory) 515, IEEE 515.1, and CAN/USA C22.2 No. 130-03 : Listing file number: 3151992
Size in Feet 2' x 36' (2x36 feet)
Size in Inches 24" x 432" (24x432 inches)
Size in Meters 0.61m x 10.97m (0.61x10.97 meters)
Warranty from Manufacturer 10 Year backed by USA Manufacturer since 1873
Amp Draw 13
Wattage per SF 50
Total Watts 3600W
Why Helps

ProMelt Mats install faster and easier than any snow melting system in 3 easy steps once you have read all instructions, planned the electrical details, designed a layout and prepared your jobsite:

  1. Roll out the mats onto prepared base surface or wire mesh/rebar
  2. Make turns by cutting tape and fitting mat to any shape area and around obstacles or up steps
  3. Secure to base or mesh using mat tape, nails or zip ties

The ProMelt radiant heating mats are built tough for Permanent installation within virtually any surface to provide efficient melting of snow and ice automatically. They must be completely embedded and at least 1.25 inches below the top of the new layer.

  • New Concrete Surfaces install in top 2 inches secured to rebar or wire mesh on supports/chairs
  • New Asphalt on top of base layer. ProMelt's polyurethane outer insulation layer withstands 300 Degrees F
  • Pavers or brick set in compacted sand beds or in mortar
  • Stone or tile set in thickset mortar. Building Code requires all outdoor systems to be 1.25 inches below the top of the new surface
  • Not for use in gravel or dirt - must be embedded as described above
Wire Construction ETFE Fluoropolymer, Braided copper ground plane, Foil shield and Outside polyurethane jacket
Write Your Own Review
You're reviewing:ProMelt · 2' x 36' Foot [13.0A] Electric Snow Melting Mat (277V / 50W)
Your Rating
Customers also purchased