SunTouch TapeMat WiFi
Everything you need for a time-saving electric floor heating system install!
Upgraded Deluxe TapeMat Kit with the ConnectPlus Wifi Programmable Thermostat!
• 24" Wide SunTouch TapeMat radiant floor heating mat w/ 10 ft power lead
• SunStat ConnectPlus WiFi Programmable Touchscreen Thermostat
• Sensor Wire - 15 feet long (inside thermostat box)
• LoudMouth Installation Alarm (continuity monitor)
• Double-stick tape - 1 extra roll
SunTouch’s open-weave mesh TapeMat can be installed in one day. There’s no need to wait for mortar to cure overnight before laying tile.
You can achieve warm floors in four easy steps. Simply unroll and attach your mat(s), secure the floor sensor (comes with all SunTouch thermostats), apply thin-set mortar, and install your flooring.
Additional Features & Benefits of the SunTouch TapeMat include:
• Edged with double-sided tape for fast & easy installation that adheres directly to your subfloor.
• Mortar bonds easily through mesh with the underlying material.
• Only 1/8" added floor thickness compared to typical tile installations
• Easily adjusted to accommodate curves, angles, and cut-outs
• Can be trimmed & flipped to accommodate your layout (only cut orange mesh)
• Also available in 2.5' & 3' wide rolls
Instructions + Video
INTERIOR floor heating application only. Embedded in mortar or self leveling concrete only.
Plan Your Layout
Measure and draw a layout simple plan (or send it to us and let us draw a layout for you) mark your Thermostat location (starting point for mats) and what areas you want to warm. Expect to place mats everywhere you want warmth heat does not spread
Roll Out Mat(s)
Turn and cut mesh (if needed) to custom fit to your room. Attach mat to subfloor with the built-in tape then mount the SunStat and place floor temperature sensor between 2 heating wires.
Cover with Mortar
Cover mats with a cement based mortar, let it cure, then install your floor covering. If you are installing tile, you can install the tile when you apply the mortar. Connect mat power leads to your thermostat in parallel.
50° Degrees F / 10° Degrees C
|Mats or Wire||Supply Wire||Breaker|
|120||up to 12 amps||14||1||single pole||15 or 20 A|
|120||up to 15 amps||12||1||single pole||20 A|
|240||up to 12 amps||14||1||double pole||15 or 20 A|
|240||up to 15 amps||12||1||double pole||20 A|
* Recommended only. Follow local codes for wire gauge size.
20 A Breaker
Yes, can be installed in a tiled shower. UL listed, verify local code
Minimum 3/8" x 1/4". Dependent on tile size - verify with tile/mortar manufacturer.
Install 4-6" away from the toilet drain wax ring. It can be under the front of toilet - Approximately 20" from wall.
|Heating Power Output Total||410 BTU total|
|Heating Power Output per Hour (BTU)||41 BTU per Sq Ft/Hour|
|EMF (Electro Magnetic Field)||Yes. Verified by Independent Testing Laboratory as ultra low. REET test|
|Ohms Reading (resistance value)||102-125 ohms|
|Power Lead Wire Gauge||18 AWG|
|Power Lead Length||10'|
|Power Lead Type||Armored, NEC color code, Single point connection at 1 corner of mat. No return wire like inferior products|
|Thickness||0.122 (less than 1/8")|
|Wattage per SF||12|
|Spacing of Heating Wire||3"|
|Heated Area in Sq Ft typical||10|
|Safety Listing||UL (Underwriters Laboratory) Listed for U.S. and Canada under UL 1673 and CAN/CSA C22.2 No. 130-03, File No. E185866|
|Length of Heated Area (ft)||5'|
|Length of Heated Area (in)||60"|
|Warranty from Manufacturer||25 Year backed by 140 year old USA Manufacturer|
|What's In The Box||TapeMat, SunStat ConnectPlus WiFi Programmable Touch Screen Thermostat, Floor Sensor, LoudMouth, Sm. Roll of Double-sided Tape, Detailed Installation Manual.|
|Wire Construction||ETFE Fluoropolymer insulation, metal shield and Outside layer of PEX combined with heating elements|
|Total Watts||120 watts|
|Size in Feet||2' x 5'|
|Size in Inches||24" x 60"|
|Size in Meters||0.61m x 1.52m|
|Acceptable Floor Coverings||Natural Stone,Tile, Laminate, Engineered Woods, Carpet, Vinyl, Linoleum, Solid Hardwood (if you use sleepers)|