FREE SHIPPING on orders over $149* (exclusions apply) See Details

SunTouch TapeMat 30"x 10' (120V)

SKU# 12001030ST

More Views

Retail: $299.00

You Save: $101.00



FREE Shipping

This item is eligible for FREE standard shipping!


Save valuable time on your electric floor heating installation!

SunTouch’s open-weave mesh TapeMat can be installed in one day. There’s no need to wait for mortar to cure overnight before laying tile.
You can achieve warm floors in four easy steps. Simply unroll and attach your mat(s), secure the floor sensor (comes with all SunTouch thermostats), apply thin-set mortar, and install your flooring.

  Edged with double-sided tape for fast & easy installation that adheres directly to your subfloor.
  Mortar bonds easily through mesh with the underlying material.
  Only 1/8" added floor thickness compared to typical tile installations
  Easily adjusted to accommodate curves, angles, and cut-outs
  Can be trimmed & flipped to accommodate your layout (only cut orange mesh)
  Also available in 2' & 3' wide rolls

Installation Demo

Instructions + Video

Instructions + Video

Instruction Manual
Install Steps

Installation Steps:

Suntouch TapeMat Installation - Step 1

Step #1

Suntouch TapeMat Installation - Step 2

Step #2

Suntouch TapeMat Installation - Step 3

Step #3

Plan Your Layout
Measure and draw a layout simple plan (or send it to us and let us draw a layout for you) mark your Thermostat location (starting point for mats) and what areas you want to warm. Expect to place mats everywhere you want warmth heat does not spread

Roll Out Mat(s)
Turn and cut mesh (if needed) to custom fit to your room. Attach mat to subfloor with the built-in tape then mount the SunStat and place floor temperature sensor between 2 heating wires.
Cover with Mortar
Cover mats with a cement based mortar, let it cure, then install your floor covering. If you are installing tile, you can install the tile when you apply the mortar. Connect mat power leads to your thermostat in parallel.
Skill Level Should be installed by qualified persons only. Electrician recommended for all wiring.
Distance from Toilet Install 4 - 6 inches away from wax ring; can be under front of toilet. Approx 20" from wall
Electrical Box Size Extra-deep single-gang box to fit power leads from 1 or 2 mats.

For 3 sets of power leads, use a 4" square deep box (you'll need the extra room for the wire, wire nuts, and thermostat control unit)
GFCI / GFEP Protection Required for each circuit. Built into all SunTouch thermostats.
Power Supply & Wiring
Mats or WireSupply WireBreaker
VACtotal amps(AWG*)qtytyperating
120up to 12 amps141single pole15 or 20 A
120up to 15 amps121single pole
20 A
240up to 12 amps141double pole15 or 20 A
240up to 15 amps121double pole20 A

* Recommended only. Follow local codes for wire gauge size.

Maximum Circuit Overload Protection 20 Amp Breaker
Maximum Circuit Load 15 Amps
Minimum Install Temperature 50 Degrees F / 10 Degrees C


Voltage 120 VAC
Size in Feet 2.5 x 10 feet
Size in Inches 30 x 120 inches
Size in Meters 0.76 x 3.05 meters
Thickness 0.122 inch (less than 1/8")
Amp Draw 2.5
Wattage per SF 12
Heating Power Output per Hour (BTU) 41 BTU per Sq Ft/Hour
Heating Power Output Total 1025 BTU total
Power Lead Length 10 feet
Power Lead Wire Gauge 18 AWG
Spacing of Heating Wire 3" inches
Resistance Value 44-54 Ohms
More Details

More Details

Manufacturer Watts Radiant
Warranty 25 year limited warranty backed by USA Manufacturer since 1874
Layout Flexibilty Adjustable to any layout, orange mesh part of the mat can be cut, blue wire can be pulled out and run around tight spaces like around the base of a toilet. NEVER cut the heating element (blue wire).
Thermostat Control Required? Yes - browse SunTouch thermostats
Conduit Required? Conduit does make installation easier in new construction (not required).
Power Lead Type Armored, NEC color code, single point connection at 1 corner of mat.
(No return wire like inferior competing products have.)
Wire Construction ETFE Fluoropolymer, metal shield and Outside layer of PEX
Minimum Bend Radius 1 inch
Acceptable Sub-Floors Installs overtop plywood, backer board, or concrete
Shower Installation Yes, can be installed in a tiled shower. UL listed, verify local code.
Indoor/Outdoor? INTERIOR floor heating Application only. Embedded in mortar or self-leveling concrete only.
Total Watts 300 watts
Repair Information Wire can be repaired. Using a LoudMouth Alarm during your install is highly recommended. Repair kits and assistance available as needed.
Safety Listing UL (Underwriters Laboratory) Listed for U.S. and Canada under UL 1673 and CAN/CSA C22.2 No. 130-03, File No. E185866
Acceptable Floor Coverings Natural Stone,Tile, Laminate, Engineered Woods, Carpet, Vinyl, Linoleum, Solid Hardwood (if you use sleepers)
EMF (Electro Magnetic Field) Verified by Independent Testing Laboratory as ultra low (REET test)

You might also like...

  1. SunTouch ShowerMat 28" x 52" (120V)

    SunTouch ShowerMat 28" x 52" (120V)

    Leave the First Review
    Learn More
  2. SunTouch ShowerMat 39" x 39" (120V)

    SunTouch ShowerMat 39" x 39" (120V)

    Leave the First Review
    Learn More
  3. KERDI-SHOWER-KIT 32" x 60" Centered Stainless Steel Drain with PVC Flange

    KERDI-SHOWER-KIT 32" x 60" Centered Stainless Steel Drain with PVC Flange

    Leave the First Review

    Retail: $569.94

    You Save: $56.99


    Learn More
  4. SunStat Command Programmable Thermostat

    SunStat Command Programmable Thermostat

    Retail: $210.00

    You Save: $21.00


    Learn More


Write Your Own Review

  • The instructions provided made the installation easy.

    The instructions provided made the installation easy.We love the heated floor.

    Posted on April 28, 2014 by Danny and Betty

  • Geat product

    We have installed the mat during summer and will not know full enjoyment until this winter. From testing it in our air conditioned home the mat warmed to several different temp. settings, we could feel the warmth.
    The installation went fine with the exception that a lead wire was cut during installation and went undetected until floor was...

    Posted on October 28, 2013 by David

View All Reviews

Have a question?

Check out our Knowledge Center

or give us a call!


Mon - Fri 6:00am to 5:00pm PST